Warning Signs of Chimney Fire from Clean Sweep Chimney Service Milwaukee

The combustion process when wood is burned is never complete. The smoke from a wood fire usually contains a dark brown or black substance which has an unpleasant odor. This tar-like substance is called creosote and is found almost anywhere in a wood heating system.

At temperatures below 250 degrees F creosote will condense on the surfaces of stove pipes or chimney flues. When the temperature gets below 150 degrees F the creosote deposit will be thick, sticky and similar to tar. This tends to trap carbon from smoke which dries and bakes inside pipes and flues. This flaky substance is very flammable.

Creosote is more of a problem with wood stoves than fireplaces since the exhaust gases from stoves are cooler than those from the fireplaces.

The amount of creosote condensing on the surfaces of the system varies according to the density of the smoke and vapor from the fire (less smoke means less creosote),the temperature of the surface on which it is condensing (higher temperatures reduce chance of creosote condensation) and the type and dryness of wood being burned.

Creosote may build up to a considerable thickness on the interior surface of the chimney and the draft opening may subsequently be reduced. A serious fire may be ignited if creosote is allowed to build up. Most problems with creosote are due to poor chimneys with a low draft and cold walls.

You can reduce the creosote problem several ways. Smoke density can be lowered somewhat in an airtight stove by using small amounts of wood and stoking more often or by using larger pieces of wood. Creosote formation can be limited by leaving the air inlet or stove door slightly open after adding wood to promote more rapid burning until the wood is mostly reduced to charcoal. Then close the inlet as desired.

Allowing this extra air causes more complete combustion lowers the potential creosote-forming gases and generates additional heat to the surrounding area. Vapor in the flue gases may be controlled by using the driest wood possible and using only small pieces of wood during mild weather when combustion is relatively slow. The stack  temperature can be raised by insulating the stove pipe connection so that it cools as little as possible before reaching the chimney. Using an insulated pipe also aids in increasing the stack temperature.

Draft can be increased by having as few bends as possible between the appliance and the chimney, having the proper height and diameter, keeping the chimney in good repair and by having a separate flue for each appliance. Also use proper sized stove pipe. In a large chimney, draft can be increased by decreasing the flue size. This can be done by installing a new smaller flue or a stainless steel stove pipe liner.

In many airtight stoves, a sealed overnight fire will deposit creosote even with dry hardwood. To dry the creosote always open the draft caps and let the fire burn hot for at least 5 minutes every morning and again before bedtime.

Opening the direct draft damper 20 to 30 minutes to dry the creosote in chimneys is a questionable practice. This should only be done in a new or clean chimney and should be done daily or every time you use the wood stove.Allowing hot flame in the chimney at intermittent times can result in a small chimney fire. The heat generated from these hot flames also may cause deterioration of the metal or crack mortar in the chimneys.

Be Prepared for A Chimney Fire

No wood burning system is 100% safe and fire-proof. A safe installation and extra care help prevent fire, but accept the idea that there could be a fire, and be prepared to handle it. Chimney fires are most likely to occur during a very hot fire, as when cardboard or Christmas tree branches are burned or even when a stove burns normal wood but at a higher than normal rate.

Make certain everyone in the house is familiar with the warning signs of a chimney fire --- sucking sounds, a loud roar and shaking pipes. Instruct everyone on what to do in case of fire. Practice fire drills and instruct all adults on how and when to use a fire extinguisher. Put the fire department phone number in an obvious place near the phone.

If you have a chimney fire:

a) Call the fire department immediately.

b) If all the stove pipe joints are tight and no other appliance is connected to the same flue, close all openings and draft controls if you have an air-tight stove. Close the stove pipe damper in a non-air-tight stove.

c) You can attempt to cut off the air supply to a fireplace by using a wet blanket or sheet metal to seal off the fireplace opening. Be careful since a strong draft can make this difficult and dangerous. Use only non combustible materials.

d) If you have a leaky stove or fireplace you may have to wait for the fire to burn out.

e) Get everyone out of the house, and put them to work watching for sparks or signs of fire on the roof or nearby. One adult should stay in the house to check the attic and upper floors for signs of fire.

f) Discharge a class ABC dry chemical fire extinguisher or throw baking soda into the stove or fireplace if the chimney is not sound or there is a danger of the house or surroundings catching on fire. The chemical travels up the chimney and often extinguishes the flame.

g) Throwing water in a stove will cause the metal to warp, but if it's a choice between the house or the stove, use water.

h) Check the chimney after a fire. A chimney fire can range from 2000 to 3000 degrees F which is hot enough to cause deterioration of metal or cause masonry to weaken. Metal chimneys can deteriorate after 2 or 3 fires.

i) If a chimney fire occurs once, chances are that it will occur again. Find the cause.

A problem with frequent chimney fires is the possibility of the framing catching on fire. The ignition temperature of new house framing is about 500 degrees F Over a period of years, as this wood is repeatedly heated by chimney fires, the wood will ignite at a much lower temperature.

Chimney Cleaning

Chimneys need to be cleaned to remove creosote and soot deposits. This will prevent chimney fires and improve the draft as well. How often the chimney is cleaned depends on how frequently the wood burning appliance is used, how it is operated and the type of installation. Some authorities recommend cleaning the chimney after every third cord of wood is burned and most recommend at least once a year. Any time you observe excessive soot and creosote, the chimney should be cleaned. After you once have cleaned the chimney, you may want to check it after 2 weeks, 1 month, 2 months, etc., to determine how often your chimney needs to be cleaned.
ln addition to cleaning your chimney, a good chimney sweep can act as a inspector for your installation.

Clean Sweep Chimney Service is located in Southeastern Wisconsin and services Milwaukee, Waukesha, Slinger, and the entire Southeastern Wisconsin area. If you need Chimney repair or Chimney Cleaning Call us at (414) 483-9996. Our Website is at http://cleansweepchimney.vpweb.comhttp://cleansweepchimney.vpweb.com